top of page
This method specifies a test for determining the ignitability of products by direct small-flame impingement under zero impressed irradiance using vertically oriented test specimens.

Flame Source Test

This method specifies a test for determining the ignitability of products by direct small-flame impingement under zero impressed irradiance using vertically oriented test specimens.

GET A QUOTE

Flame Source Test

What is a Small Flame Source test?


This method specifies a test for determining the ignitability of products by direct small-flame impingement under zero impressed irradiance using vertically oriented test specimens.

 

The test specimens are cut from a sample which is representative of the product to be tested (e.g. it shall be tested as an assembly of component and not individually). When a substrate is used a specimen must be tested with a substrate representative of the end-use application.

 

Each specimen is 250 ±2mm long and 90 ±2mm vide and are conditioned in accordance with 2.3.

 

The samples are tested with 2 exposure conditions to a 20mm flame:

​

  • Surface exposure – 40mm above bottom edge

  • Edge exposure – at the bottom of the specimen


6 samples must be tested in each exposure – a total of 12 samples.

​

The flame is applied for 15 or 30s, depending on the classification sought.

​

The pass/fail criteria for classification are spread of flame to 150mm for the application of the burner flame.



UKAS Accredited Laboratory


Our UKAS accredited testing laboratory No. 21542 can provide full end-to-end fire testing services alongside fire resistance testing.



​Comprehensive Report


‍Once your test is completed, you will be issued with a comprehensive and internationally recognised fire resistance test report accessible by your very own online portal with a full video of the test conducted.


​

What product classifications require BS EN ISO 11925-2 testing?


The Single Source Flame (BS EN ISO 11925-2:2026) test would be required in order to achieve a product classification of B, C, D, E and F:

A1
A2
B
C
D
E
F
NO
NO
Yes
Yes
Yes
Yes
Yes

BS EN ISO 11925-2:2026 was published on 31st January 2026 and supersedes the BS EN 11925-2:2020, which is now withdrawn.


We provide accredited independent fire door testing services and fire resistance testing for door hardware and ironmongery.

Doorsets and Hardware Testing

Start Now
We provide accredited independent wall and partition testing services to ensure compliance with the highest standards required.

Wall & Partition System Testing

Start Now
We provide accredited independent glazing systems testing services to ensure compliance with the highest standards required.

Glazing Systems Testing

Start Now
The purpose of fire resistance testing is to confirm compliance with building codes and standards, ensuring the seals maintain their protective properties during a fire.

Penetration Seals Testing

Start Now
The purpose of fire resistance tests on linear joint seals is to assess the effect of a linear joint seal on the integrity and insulation of the construction.

Linear Joint Seals Testing

Start Now
Horizontal floor & ceiling fire testing services from a UK-based laboratory.

Floors and Ceilings Testing

Start Now
​UKTC's smoke leakage chamber enables comprehensive and UKAS accredited smoke leakage testing performed to either BS EN 1634-3:2004 or BS 476-31.1:1983.​​

Smoke Leakage Testing

Start Now
Coming Soon to UKTC's laboratory and test facility, a purpose-built acoustic test suite in accordance with BS EN ISO 10140-5:2021.

Acoustic Testing

Start Now
This procedure specifies a method of test for determining the rection to fire performance of construction products when exposed to thermal attack by a single burning item (SBI).

Single Burning Item (SBI) Test

Start Now
This test identifies products that will not, or not significantly, contribute to fire, regardless of their end use.

Non-combustibility Test

Start Now
This test determines the potential maximum total heat release of a product when completely burned, regardless of its end use.

Gross Heat of Combustion Test

Start Now

other tests we provide

Trusted to ensure

Underline_2.png

Our team consists of the brightest scientists, engineers, researchers and technicians from the built environment industry. We share a common goal - to enable greater protection of lives and assets - and are ready to help you.

SPEAK TO US

FREQUENTLY ASKED QUESTIONS

bottom of page