top of page
This procedure specifies a method of test for determining the rection to fire performance of construction products when exposed to thermal attack by a single burning item (SBI).

Single Burning Item (SBI) Test

This procedure specifies a method of test for determining the rection to fire performance of construction products when exposed to thermal attack by a single burning item (SBI).

GET A QUOTE

Single Burning Item (SBI) Test

This procedure specifies a method of test for determining the rection to fire performance of construction products when exposed to thermal attack by a single burning item (SBI).

​

The test specimen consists of 2 vertical wings forming a right-angled corner. The dimensions of the wings are:

 

  • The long wing: 1500mm high x 1000mm long.

  • The short wing: 1500mm high x 500 + (thickness of long wing) mm long


  • The maximum thickness shall be no more than 200mm. If the product is thicker than 200mm, then thickness shall be reduced on the unexposed side.

The samples must be conditioned, a minimum of 3 samples must be tested. The extraction is set to a volume flow of 0.6=-0.05m³/s

Each test specimen is then fixed in the trolley and is exposed to a flame from a burner placed at the bottom of the corner. The flame is obtained by combustion of propane gas and gives heat output of 30.7±2kW. The flame is applied for 20 mins.



What does the test apparatus measure?


The test apparatus measures the following:


  • Temperatures of exhaust gases

  • Volume flow in the exhaust

  • Light attenuation (for measurement of smoke density)

  • O2 and CO2 mole fraction of the exhaust gases.


These quantities are recorded automatically and are used to calculate the Heat Release Rate (HRR) and Smoke Production Rate (SPR). A visual observation is also measured for flaming droplets an horizontal spread of flame.

 

HRR is used to calculate FIGRA (fire growth rate) at 0.2 and 0.4MJ, and SPR is used to calculate SMOGRA (smoke growth rate).



UKAS Accredited Laboratory


Our UKAS accredited testing laboratory No. 21542 can provide full end-to-end fire testing services alongside fire resistance testing.



​Comprehensive Report


‍Once your test is completed, you will be issued with a comprehensive and internationally recognised fire resistance test report accessible by your very own online portal with a full video of the test conducted.


​

What product classifications require BS EN 13823:2020 testing?


The Single Burning Item (BS EN 13823:2020) test would be required in order to achieve a product classification of A2, B, C and D:

A1
A2*
B
C
D
E
F
NO
Yes
Yes
Yes
Yes
NO
NO

We provide accredited independent fire door testing services and fire resistance testing for door hardware and ironmongery.

Doorsets and Hardware Testing

Start Now
We provide accredited independent wall and partition testing services to ensure compliance with the highest standards required.

Wall & Partition System Testing

Start Now
We provide accredited independent glazing systems testing services to ensure compliance with the highest standards required.

Glazing Systems Testing

Start Now
The purpose of fire resistance testing is to confirm compliance with building codes and standards, ensuring the seals maintain their protective properties during a fire.

Penetration Seals Testing

Start Now
The purpose of fire resistance tests on linear joint seals is to assess the effect of a linear joint seal on the integrity and insulation of the construction.

Linear Joint Seals Testing

Start Now
Horizontal floor & ceiling fire testing services from a UK-based laboratory.

Floors and Ceilings Testing

Start Now
​UKTC's smoke leakage chamber enables comprehensive and UKAS accredited smoke leakage testing performed to either BS EN 1634-3:2004 or BS 476-31.1:1983.​​

Smoke Leakage Testing

Start Now
Coming Soon to UKTC's laboratory and test facility, a purpose-built acoustic test suite in accordance with BS EN ISO 10140-5:2021.

Acoustic Testing

Start Now
This test identifies products that will not, or not significantly, contribute to fire, regardless of their end use.

Non-combustibility Test

Start Now
This method specifies a test for determining the ignitability of products by direct small-flame impingement under zero impressed irradiance using vertically oriented test specimens.

Flame Source Test

Start Now
This test determines the potential maximum total heat release of a product when completely burned, regardless of its end use.

Gross Heat of Combustion Test

Start Now

other tests we provide

Trusted to ensure

Underline_2.png

Our team consists of the brightest scientists, engineers, researchers and technicians from the built environment industry. We share a common goal - to enable greater protection of lives and assets - and are ready to help you.

SPEAK TO US

FREQUENTLY ASKED QUESTIONS

bottom of page