top of page
This test identifies products that will not, or not significantly, contribute to fire, regardless of their end use.

Non-combustibility Test

This test identifies products that will not, or not significantly, contribute to fire, regardless of their end use.

GET A QUOTE

Non-combustibility Test

What Is A Non-Combustibility Test?


This test identifies products that will not, or not significantly, contribute to fire, regardless of their end use.


The fire test has been developed to selected construction products which produce a very limited amount of heat and flame when exposed to temperatures of approximately 750 °C.


The test specimen shall be taken from a sample which is sufficiently large to be representative of the product and shall be cylindrical with a volume of 76 ± 8cm³ and diameter of 45+0mm and a height of ± 3mm.


For non-homogenous (e.g., layered, or composite products) – each component or layer shall be tested separately.


A minimum of 5 samples shall be tested for classification.


After conditioning the samples must be dried in an oven at 60±5°C for 20-24hr. Prior to testing each sample is weighed to an accuracy of 0.01g.


The samples are then inserted into a furnace that has been stabilised at 750 ±5°C for a minimum period of 30 min. The following data is recorded:


  • Temperature of the furnace

  • Temperature of the specimen centre and surface

  • Any sustained flaming (3s or longer)



The sample is then removed, allowed to cool, and weighed again. The test report will show:


  • Mass loss (%) of each sample.

  • Temperature rise of each sample

  • Any sustained flaming



UKAS Accredited Laboratory


Our UKAS accredited testing laboratory No. 21542 can provide full end-to-end fire testing services alongside fire resistance testing.



​Comprehensive Report


‍Once your test is completed, you will be issued with a comprehensive and internationally recognised fire resistance test report accessible by your very own online portal with a full video of the test conducted.


​


What product classifications require BS EN ISO 1182 testing?


The Non-Combustibility (BS EN 1182:2020) test would be required in order to achieve a product classification of A1 and A2*:

A1
A2*
B
C
D
E
F
Yes
Yes
NO
NO
NO
NO
NO

*not required if conducting BS EN ISO 1716 test

We provide accredited independent fire door testing services and fire resistance testing for door hardware and ironmongery.

Doorsets and Hardware Testing

Start Now
We provide accredited independent wall and partition testing services to ensure compliance with the highest standards required.

Wall & Partition System Testing

Start Now
We provide accredited independent glazing systems testing services to ensure compliance with the highest standards required.

Glazing Systems Testing

Start Now
The purpose of fire resistance testing is to confirm compliance with building codes and standards, ensuring the seals maintain their protective properties during a fire.

Penetration Seals Testing

Start Now
The purpose of fire resistance tests on linear joint seals is to assess the effect of a linear joint seal on the integrity and insulation of the construction.

Linear Joint Seals Testing

Start Now
Horizontal floor & ceiling fire testing services from a UK-based laboratory.

Floors and Ceilings Testing

Start Now
​UKTC's smoke leakage chamber enables comprehensive and UKAS accredited smoke leakage testing performed to either BS EN 1634-3:2004 or BS 476-31.1:1983.​​

Smoke Leakage Testing

Start Now
Coming Soon to UKTC's laboratory and test facility, a purpose-built acoustic test suite in accordance with BS EN ISO 10140-5:2021.

Acoustic Testing

Start Now
This procedure specifies a method of test for determining the rection to fire performance of construction products when exposed to thermal attack by a single burning item (SBI).

Single Burning Item (SBI) Test

Start Now
This method specifies a test for determining the ignitability of products by direct small-flame impingement under zero impressed irradiance using vertically oriented test specimens.

Flame Source Test

Start Now
This test determines the potential maximum total heat release of a product when completely burned, regardless of its end use.

Gross Heat of Combustion Test

Start Now

other tests we provide

Trusted to ensure

Underline_2.png

Our team consists of the brightest scientists, engineers, researchers and technicians from the built environment industry. We share a common goal - to enable greater protection of lives and assets - and are ready to help you.

SPEAK TO US

FREQUENTLY ASKED QUESTIONS

bottom of page