top of page
This test determines the potential maximum total heat release of a product when completely burned, regardless of its end use.

Gross Heat of Combustion Test

This test determines the potential maximum total heat release of a product when completely burned, regardless of its end use.

GET A QUOTE

Gross Heat of Combustion Test

What is a Gross Heat of Combustion test?


This test determines the potential maximum total heat release of a product when completely burned, regardless of its end use.

 

This method determines the absolute value of the heat of combustion for a product without accounting for inherent product variability.

 

The mass per unit area of each non-substantial component must be provided by the client or calculated in the laboratory.

 

A minimum of 50g from a homogenous product or substantial component and 10g from any non-substantial component is to be sampled, ground into a fine powder and conditioned.

After conditioning a 0.5g sample is selected and placed in a crucible inside the pressurised vessel (bomb), together with combustion aids if necessary (benzoic acid or paraffin oil). The bomb is then filled with 99.5% pure oxygen to a pressure of 30MPa. The bomb is then inserted into the testing apparatus which fills with water and the sample is ignited. The test apparatus measures the rise in temperature of the water and calculates the calorific value of the sample, considering any combustion aids.

 

A total of 5 samples of each component are tested.

 

The report will show the calorific value of each project in MJ/kg, Mj/m2 for each non-substantial component, and the total calorific value of the entire product.



UKAS Accredited Laboratory


Our UKAS accredited testing laboratory No. 21542 can provide full end-to-end fire testing services alongside fire resistance testing.



​Comprehensive Report


‍Once your test is completed, you will be issued with a comprehensive and internationally recognised fire resistance test report accessible by your very own online portal with a full video of the test conducted.



What product classifications require BS en ISO 1716:2018 testing?


The Gross Heat of Combustion (BS EN 1716:2018) test would be required in order to achieve a product classification of A1 and A2*:


A1
A2*
B
C
D
E
F
Yes
Yes
NO
NO
NO
NO
NO

*not required if conducting BS EN ISO 1182 test


We provide accredited independent fire door testing services and fire resistance testing for door hardware and ironmongery.

Doorsets and Hardware Testing

Start Now
We provide accredited independent wall and partition testing services to ensure compliance with the highest standards required.

Wall & Partition System Testing

Start Now
We provide accredited independent glazing systems testing services to ensure compliance with the highest standards required.

Glazing Systems Testing

Start Now
The purpose of fire resistance testing is to confirm compliance with building codes and standards, ensuring the seals maintain their protective properties during a fire.

Penetration Seals Testing

Start Now
The purpose of fire resistance tests on linear joint seals is to assess the effect of a linear joint seal on the integrity and insulation of the construction.

Linear Joint Seals Testing

Start Now
Horizontal floor & ceiling fire testing services from a UK-based laboratory.

Floors and Ceilings Testing

Start Now
​UKTC's smoke leakage chamber enables comprehensive and UKAS accredited smoke leakage testing performed to either BS EN 1634-3:2004 or BS 476-31.1:1983.​​

Smoke Leakage Testing

Start Now
Coming Soon to UKTC's laboratory and test facility, a purpose-built acoustic test suite in accordance with BS EN ISO 10140-5:2021.

Acoustic Testing

Start Now
This procedure specifies a method of test for determining the rection to fire performance of construction products when exposed to thermal attack by a single burning item (SBI).

Single Burning Item (SBI) Test

Start Now
This test identifies products that will not, or not significantly, contribute to fire, regardless of their end use.

Non-combustibility Test

Start Now
This method specifies a test for determining the ignitability of products by direct small-flame impingement under zero impressed irradiance using vertically oriented test specimens.

Flame Source Test

Start Now

other tests we provide

Trusted to ensure

Underline_2.png

Our team consists of the brightest scientists, engineers, researchers and technicians from the built environment industry. We share a common goal - to enable greater protection of lives and assets - and are ready to help you.

SPEAK TO US

FREQUENTLY ASKED QUESTIONS

bottom of page